Industrial cyclone/Cyclone feed collector/aggregate batcher/Trimmer/cyclone for flour mill
1. No moving parts
2. multiple application no any influence
3. Good dust collection rate
Industrial cyclone are often employed as an Initial Stage Collector to lighten heavy dusts loads before being sent to a Primary Stage Fabric Collector. By removing coarse particles from the gas stream, and allowing later stage Fabric Collectors to solely remove finer particles, these collectors increase the efficiency and service life of Fabric Collectors (Baghouses) and their Filters. Thus protecting your larger and most costly investment from unnecessary wear and tear.
It often named after the cyclone weather phenomenon, are large funnel shaped sheet metal tubes connected to ducts often used in woodshops, machine shops, manufacturing plants, and powder processing plants. Dust and debris are sucked in at the top. Air containing fine dust blows out of the other side of the top, while chips and large dust particles fall out of the bottom into a drum or bin. Dusty exhaust air is either blown outside or filtered again using media filtration. Working principleAs the dirty air enters the cyclone dust collector, it is forced into a swirling movement. This results in a centrifugal force acting on the dust particles suspended in the air stream. The particles, denser than the air, are forced to move outwards, towards the cyclone dust collector wall. They then fall downwards, towards the dust exit. The clean air is eventually directed towards the centre of the cyclone and leaves through the gas exit.Cyclone dust collector efficiency is a function of the physical parameters of the particles and the design parameters of the unit. Cyclone efficiency increases with:
Coarse particle size distribution
Higher products specific gravity
Lower gas density
Smaller outlet diameter. An increase in pressure drop also results.
Characteristic The Cyclone dust collector hasn't any moving parts. It's conenient for manufacture and management. With the same air volume, The cyclone collector is more smaller size, and the price is more cheaper. As the second dedusting and matched with bag filter, it can be installed vertically, also can be installed in a horizontal. So, it is easy to install and applicate. The cyclone collector efficiency of resistance is not affected for many sets of cylcone dollector in multiple using when processing the large dust gas air volume.
Technical parameter
| Model |
Rotor Diammm |
Rotor speedr/min |
Rotor powerkw |
Air volume
(m³/h) |
Capacity (kg/h) |
comminution sizeum |
| HTC-132 |
132 |
1100~11000 |
4 |
500 |
15~300 |
3~150 |
| HTC-250 |
250 |
700~7000 |
5.5~7.5 |
2000 |
30~800 |
| HTC-315 |
315 |
500~5000 |
7.5~11 |
3200 |
50~1500 |
| HTC-400 |
400 |
450~4500 |
11~15 |
5000 |
100~3000 |
| HTC-500 |
500 |
350~3500 |
22~30 |
7000 |
200~4500 |
| HTC-630 |
630 |
250~2500 |
30~37 |
9000 |
300~6000 |
| HTC-800 |
800 |
150~1500 |
37~45 |
12500 |
400~8000 |
![]()
![]()
![]()
![]()
![]()
FAQ
1. What material you want to grind, is it dry, what is the size of feed material ?
2. What capacity you expect ? (kg/h)
3. What mesh or mm or micron(size) of the powder you want?
4. What voltage you want? For example, 380V 50hz 3p; 440V 60Hz,3p; 220V...etc.
(We only provide 3P, because our machines are all for industrial use,not for family.)
We know that a good and satisfying powder grinding mill manufacturer and supplier should not only provide
high quality products, but also complete customer services.
we provide the following services:
Technical support
Upon receiving the deposit, we will offer the following technical services:
1. Design for your production line flow and equipment layout, free of charge;
2. Provide foundation drawings of customer-ordered grinding mills and drawings of related parts, etc;
3. Technical parameters of peripheral equipment will be supplied;
4. Free technical suggestions on adjusting of equipment layout and application.
5. Equipment upgrading (customers need to pay the cost);
Quality assurance
1. Strictly conforming to ISO9001-2000 quality management system;
2. Strict control from purchasing inspection, process inspection to final proofing;
3. Established several QC departments to execute quality control regulations;
4. Detailed quality control examples:
(1) Complete files for quality control and quality feedback;
(2) Strict inspection for the components of our grinding mills, to assure products free of damage and avoid
rust-eaten and paint peeling off later on.
(3) Only qualified components will be assembled and total equipment must be inspected completely before
sale.
After sale service
1. We will send our technician to the site for guiding equipment installation and commissioning.
2. During the installation and commissioning, we offer operator training service.
3. The quality assurance date is one year after commissioning. And after that, we will collect the cost if
provide repairing for your equipment.
4. Maintenance for equipment failure caused by improper handling (appropriate cost will be collected).
5. We offer the components with favorable price and perdurable maintenance.
6. If equipment repairing is needed after quality assurance date is expired, we will collect maintenance cost.
Welcome to visit our factory !
